Ok so I actually found a good deal on Amazon Prime day for something that’s useful (I think)…the direct sprite extruder is $30 off (in Canada). Seems to have good reviews, but I don’t know what it actually improves. My printer gets about as much TLC as my hammers, and aside from this under-extrusion bs I’ve been trying to figure out, it’s still banging out prints. Thoughts?

Thanks!

  • ffhein@lemmy.world
    link
    fedilink
    English
    arrow-up
    7
    ·
    1 year ago

    but I don’t know what it actually improves

    Depends on what you’re upgrading from.

    I don’t have this extruder, I’ve heard it’s ok but I can’t vouch for it personally. However I can tell you how it differes from a stock Ender 3/pro/v2 if that’s what you’re coming form. To avoid confusion it might be worth mentioning that the word “extruder” is a bit ambiguous in 3d printing, but when talking about printer hardware most people use it to only mean the motor and drive gears for the filament.

    The stock Ender 3, and many other printers, have bowden drive which means that the extruder is mounted on the printer’s frame, and the extruder pushes the filament into a tube leading to the hotend. This kit changes the printer to direct drive, where the extruder is mounted right on top of the hotend. This can reduce print artifacts since it shortens the filament path, but printer firmwares also have features to compensate for this (pressure advance in Klipper and linear advance in Marlin IIRC). The disadvantage with direct drive is that it adds weight to the toolhead, which can cause ringing (a.k.a ghosting) artifacts at higher print speeds. However the Sprite has a geared extruder so it uses a smaller and lighter stepper motor so I don’t think that’s anything to worry about. Klipper firmware can compensate for toolhead weight (resonance compensation) but I don’t know if Marlin has got that yet. Either way, having a direct drive extruder will allow you to print flexible filaments.

    Speaking of geared extruders… When melting filament and pushing it through the nozzle, the amount of force needed is going to increase the faster you try to do it. When the required force exceeds what your printer can deliver then it’s going to start underextruding. If you have this issue you can see that printed lines will look thin in the middle, and thicker where the nozzle changes direction and the printer moves more slowly. This problem can be fixed by printing slower if you don’t want to upgrade the printer. An extruder with a gear ratio will be stronger, so it can be more consistent with the amount of extruded filament.

    The stock Ender 3 etc. have a hotend where the bowden tube, which is made of PTFE a.k.a. teflon, goes all the way down to the melt zone. This slightly reduces the risk of clogs, but it also means that you never should print above 220C because the teflon degrades at higher temps and begins to release toxic gases. This kit appears to have an all metal hotend, so the PTFE tube is kept away from the hot parts of the hotend, which is why the product description says you can print up to 300C.

    As for this particular hotend/extruder kit, I think the main advantage is that it’s a very easy and convenient upgrade. I think the quality is ok, but if you like the idea of modding there are plenty of other options. If you buy parts (hotend, extruder, fan, light weight stepper motor) from well respected manufacturers and print the carriage and fan duct yourself I think it’s possible to get a solution that is better in every way (lighter, stronger extruder, more efficient hotend, more cooling) for about the same amount of money. However I don’t think you’ll really notice much difference compared to this kit, and I don’t think it’s worth it unless you really enjoy the modding process. If you buy a Bondtech high flow nozzle you’ll probably get really good performance from the Sprite.

      • rug_burn
        link
        fedilink
        English
        arrow-up
        2
        ·
        1 year ago

        A agree with what was said above, but I have to add that if you decide to go with direct drive you’ll also need to take the time to dial in your retraction distance and speed in your slicer. When my E3V2 stock extruder teeth wore out, I went all in and got a Microswiss NG direct drive extruder/hotend. If you don’t dial in your retraction distance and speed you will likely get tons of ooze. You’ll also need to recalibrate pretty much everything from your z offset, e-steps, input shaping if you use kilpper, belt tension… the works. Is it worth it? That depends. In my case, yes it was, buy ymmv

  • CIA_chatbot@lemmy.world
    link
    fedilink
    English
    arrow-up
    3
    arrow-down
    1
    ·
    1 year ago

    Anything is better then the stock extruder setup that comes with Enders. If you are under extruding, calibrate your esteps. Extruder teeth wear out over time.

    That being said, the sprite is def. a step up from stock and 30 bucks off is a pretty decent deal

      • CIA_chatbot@lemmy.world
        link
        fedilink
        English
        arrow-up
        2
        ·
        1 year ago

        That’s not true, those gears (especially in the stock ender Bowden setups) are extremely trash. It doesn’t even take a lot of filament to get visible wear on the teeth to the point you get slippage.

        Coupled with it being a single gear means wear on the teeth is even more prone to failure.

        There’s a reason all of the higher quality extruders are double gear and hardened steel teeth vs. bronze. Just like nozzles wear out so do extruders

          • CIA_chatbot@lemmy.world
            link
            fedilink
            English
            arrow-up
            1
            ·
            1 year ago

            Not really, first thing is going to happen is it’s going to start under extruding and the flow is interrupted (trust me I have multiple ender 3’s, I’ve lived this :D )

            Eventually no amount of adjusting will fix it, but at the start you’ll just get some weird layer lines, under extrusion, retraction issues. It’ll just get worse and worse

            I REALLY hate the ender extruders hehe. I do have to admit they did train me to troubleshoot extruder issues really well though

  • oct2pus@kbin.social
    link
    fedilink
    arrow-up
    2
    ·
    1 year ago

    As an extruder its fine, I will say cooling shrouds tend to be very bulky and the default cooling isn’t very good.

  • ZeroCooler@lemmy.world
    link
    fedilink
    English
    arrow-up
    1
    ·
    1 year ago

    I recently upgraded my Ender 3 to the Sprite. My two main reasons were:

    1: it’s all metal (the pro is at least) . I wanted the option of printing in ABS (if I some day have the time to do that)

    2: it makes it so much easier for me to change out the filament.

    I’m by no means a pro 3D printer, I mainly use mine to support other hobbies. I also like that I can print much faster with the Sprite (or so I think). I’ve also been printing almost exclusively in PETG since I got the Sprite.

    Overall, I think it was a good investment. Could I have survived with the stock extruder? Absolutely, but I’m happy with the purchase overall.

    Hope this helps!