the lower voltage they operate at calls for more attention to be paid to signal integrity between the CPU and memory
And they aren’t kidding around, modern high speed signals are so fast that a millimeter or less of difference in length between two traces might be enough to cause the signals to arrive at the other end with enough time skew to corrupt the data.
Edit: if you ever looked closely at a circuit board and seen strange, squiggly traces that are shaped like that for seemingly no reason, it’s done so that the lengths can be matched with other traces.
USB3 is quite forgiving regarding the layout. The standard ±10% impedance matching is fine, and because there is no dedicated clock line you don’t need to do length matching either. Even differential pair length mismatch is not that big of a deal. If 0.1mm is easy to archive, sure go for it, but I’d rather compromise on this in favor of more important parameters.
Same, but now I’m working on very high-speed stuff for work and starting to get into that hobby-wise as well. Just yesterday had a conversation with a colleague about how things are getting too small to hand-solder.
My dedicated AI machine uses 1866mhz DDR3. Consumers don’t know what they need and will buy whatever the latest new thing is. Smart phones are so dumb. Like wow, your brand new $2500 phone has a benchmark 4x faster than my refurbished $250 phone. Now tell me what you do with all that power. “…well I save 27ms per Instagram post which adds up with how much I use it”. I want to run headfirst into a brick wall.
A couple old metrology equipment dated back from the 80s I still use calls them ‘mil’. It’s got dual dials for mil/mm. Gets me confused sometimes because the gauge can go down to couple millionths of an inch/couple 10s of nanometers.
Yeah, I’ve never heard of that before either. What I have heard of is either MOA or MIL reticles. In that context a Mil stands for milliradian, which is a representation of angle. That definitely doesn’t track with the post though.
And it’s especially confusing for people who use sane measurement systems where “mil” is short for “millimetre”, because it’s just the start of the word. I think anyone that still insists on measuring things in thousandths of an inch should keep their own bespoke lingo too, and everyone else should steadfastly refuse to acknowledge “mil” in this context.
In the design and manufacture of PCBs (aka circuit boards) a “mil” is a one thousandth of an inch, so it makes sense that’s what is being used in this context.
Also the maths check out: 0.005 inches is equal to aprox 0.12mm, “just over 0.1mm”.
Yeah, I found it wierd too when I started designing PCBs (as hobby) that “mill” actually stood for thousanth of an inch.
Probably for historical reasons, there are tons of things in the older domains within electronics that are based on inches rather than metric units: for example the spacing between the legs of a microchip in the older chip package formats (so called DIP, the ones with legs that go into holes) is exactly 0.1"
The sizes in more modern electronics isn’t usually based on inches anymore, but circuit boards are old tech (even if done with new materials) so there are still a number of measures in there which are based on inches.
And they aren’t kidding around, modern high speed signals are so fast that a millimeter or less of difference in length between two traces might be enough to cause the signals to arrive at the other end with enough time skew to corrupt the data.
Edit: if you ever looked closely at a circuit board and seen strange, squiggly traces that are shaped like that for seemingly no reason, it’s done so that the lengths can be matched with other traces.
A millimeter is huge in these situations. USB3 requires 5 mil tolerances, just over 0.1 mm. This scales with the inverse of data rate.
Electronics are so fast that we gotta take the speed of light into account. God help you if you put too sharp a bend in a trace, too …
USB3 is quite forgiving regarding the layout. The standard ±10% impedance matching is fine, and because there is no dedicated clock line you don’t need to do length matching either. Even differential pair length mismatch is not that big of a deal. If 0.1mm is easy to archive, sure go for it, but I’d rather compromise on this in favor of more important parameters.
That’s why serial busses won over parallel ones I guess.
Haha, I’m still over here messing with 10/100 Ethernet and USB 2 on my home projects. I’m used to bigger tolerances than the truly high tech stuff.
Same, but now I’m working on very high-speed stuff for work and starting to get into that hobby-wise as well. Just yesterday had a conversation with a colleague about how things are getting too small to hand-solder.
My dedicated AI machine uses 1866mhz DDR3. Consumers don’t know what they need and will buy whatever the latest new thing is. Smart phones are so dumb. Like wow, your brand new $2500 phone has a benchmark 4x faster than my refurbished $250 phone. Now tell me what you do with all that power. “…well I save 27ms per Instagram post which adds up with how much I use it”. I want to run headfirst into a brick wall.
I meant PCBs. I design custom circuit boards.
Like this one: https://www.tindie.com/products/bmoreautomation/esp-r8-poe-3c-automation-controller/
What is a mil in this context? I’m genuinely curious.
Probably one thousandth of an inch.
Ew.
Yes.
Hey thousands of an inch are the only part of our imperial system that actually makes sense
I’ve heard it referred to as ‘thou’ but not ‘mil’
A couple old metrology equipment dated back from the 80s I still use calls them ‘mil’. It’s got dual dials for mil/mm. Gets me confused sometimes because the gauge can go down to couple millionths of an inch/couple 10s of nanometers.
LVDT for those curious.
Yeah, I’ve never heard of that before either. What I have heard of is either MOA or MIL reticles. In that context a Mil stands for milliradian, which is a representation of angle. That definitely doesn’t track with the post though.
And it’s especially confusing for people who use sane measurement systems where “mil” is short for “millimetre”, because it’s just the start of the word. I think anyone that still insists on measuring things in thousandths of an inch should keep their own bespoke lingo too, and everyone else should steadfastly refuse to acknowledge “mil” in this context.
Correct.
A millimeter i.e a thousands of a meter.
edit: I was wrong, confusingly enough it is a thousands of an inch
5 mm isn’t ‘just over 0.1 mm’. That can’t be right.
Well, it depends on your margin of error.
In the design and manufacture of PCBs (aka circuit boards) a “mil” is a one thousandth of an inch, so it makes sense that’s what is being used in this context.
Also the maths check out: 0.005 inches is equal to aprox 0.12mm, “just over 0.1mm”.
I stand corrected, and I see I didn’t read the comment thoroughly enough either.
Colloquially as a non-pcb maker I would use and hear the term “mill” as short form millimeter so I assumed it was that.
so TIL :)
Yeah, I found it wierd too when I started designing PCBs (as hobby) that “mill” actually stood for thousanth of an inch.
Probably for historical reasons, there are tons of things in the older domains within electronics that are based on inches rather than metric units: for example the spacing between the legs of a microchip in the older chip package formats (so called DIP, the ones with legs that go into holes) is exactly 0.1"
The sizes in more modern electronics isn’t usually based on inches anymore, but circuit boards are old tech (even if done with new materials) so there are still a number of measures in there which are based on inches.