Made sure the stock firmware printed the example gcode that came on the SD card and then immediately embarked on my journey to get klipper running on this guy.

I didn’t finish until the wee hours this morning so I’ve yet to really give it a go but all the essentials are operational.

Here’s the GitHub link to the config I created: https://github.com/0xD34D/ender3-v3-se-klipper-config

  • im_mr_clean@lemmy.worldEnglish
    4·
    1 year ago

    To your printer.cfg I’d add:

    [exclude_object]

    Allows you to cancel individual items. If you have multiple items printing and one fails in one way or another you can cancel just that object and continue the rest of the print. Literally the only thing is add the bracketed thing to the cfg and it’ll add a icon next to the pause button that gives you the options.

    Meh on the next part. I see that version doesn’t have bed level knobs. I’ll leave it if there is someone else who doesn’t know about it.

    I’ve also found that one of the bed screw leveling options is very helpful for getting the bed close enough for the bltouch to really be dialed in. I use

    [bed_screws] Screw1: 32.5, 202.5 Screw2: 32.5, 32.5 Screw3: 202.5, 32.5 Screw4: 202.5, 202.5

    Then in the console run: bed_screws_adjust

    Just moves the nozzle to each of the four corners right above the leveling knobs. Makes it pretty simple. I will add that the coordinates I use are fore a ender3pro but should be the same ish for you. But don’t quote me on that.

    • 0xd34dOPEnglish
      2·
      1 year ago

      So I add that as an include from another config. It’s saved me from a few complete failures 😁. For this I was trying to keep it as a basic config for others to use as a good base and I would like to submit a PR, eventually, to include it in klipper’s example configs.

    • hibbfd@kbin.social
      2·
      1 year ago

      even better, add [screws_tilt_adjust] to take advantage of the crtouch and a little fancy computer math to make leveling super easy.

      after configuring the screw locations and thread pitch, execute the command screws_tilt_calculate

      https://www.klipper3d.org/Manual_Level.html

      ender beds use M4 screws

      • 0xd34dOPEnglish
        2·
        1 year ago

        I’m going to look into adding this in, thanks for the tip!

  • MicrosoftSam@lemmy.worldEnglish
    3·
    1 year ago

    Can you give a little more info about this? I don’t know what it is. I have to Ender 3s at work and would love some kind of dashboard.

    • Calania@feddit.nuEnglish
      6·
      1 year ago

      You should try to install octoprint on a raspberry pi. It’s the easiest way to get a web gui if you don’t want to mess with the firmware or mainboard

      • LazaroFilm@lemmy.worldEnglish
        51·
        1 year ago

        Klipper is sooo much better than Octoprint. It replaced the whole software not just the web interface part. Klipper is absolutely amazing. Now for work, it’s an open source software with community support. So done corporate don’t like not having a company to blame if something goes wrong.

        • mee@programming.devEnglish
          4·
          1 year ago

          Klipper isn’t a web interface. Octoprint works with Klipper as a web interface. They’re different software for different things.

            • u_tamtam@programming.devEnglish
              1·
              1 year ago

              Octoprint has tons of great plugins and features that mainsail/fluidd have no equivalent for, and can be used to control klipper printers too.

    • hibbfd@kbin.social
      3·
      1 year ago

      klipper is the firmware flashed to the printer

      gui is achieved and accessed through mainsail or octoprint. I haven’t tried octoprint.

      mainsail runs on a raspberry pi and can manage multiple klipper printers with one device. you can also add klipperscreen, it’s an addon that can be used with a touchscreen for an interface at the printer (or anywhere really)…

      but I just access mine running mainsail through my phone browser or the laptop I use to model and slice. I like orcaslicer because it integrates mainsail right into a tab in the slicer and provides a seamless user experience.

        • hibbfd@kbin.social
          1·
          1 year ago

          another thing to note… klipper firmware takes the heavy processing typically handled by the printer control board, and offloads the burden onto the computer or device you have hooked up to the printer, processing and feeding the gcode one line at a time. so whatever device you are using needs to be up to the specs. I’m using an rpi 3b+ and have no issues.