I’m printing with PLA on a “PEO” print bed (really a textured PEI), on my heavily modified ender 3, and there’s a pattern on the bottom of my first layer that I’m trying to get rid of. The top of the first layer looks fine, and changing the z offset in either direction doesn’t help. I’ve also tried slowing down the print speed because I thought the extruder might be skipping, but I’m still seeing it at 10mm/s. Any idea what could be causing it, and how to get rid of it?

Pic: https://sh.itjust.works/pictrs/image/31cd6cef-16de-47b3-995f-197f7d0b432d.jpeg

Edit: the first layer went down from the bottom left to the top right, but the pattern I’m seeing is perpendicular to the extruder path

  • @AjenOP
    link
    English
    6
    edit-2
    15 days ago

    Layer adhesion is great.

    No, this pattern isn’t coming from the bed. The bed actually has a polygon pattern that I’m trying to get the plastic to pick up. Sellers on Amazon/ebay/Ali are calling it PEO, but it’s really just PEI with a fine texture that diffracts light. The pattern from the bed comes through really well on the perimeter of anything I print, but not the center.

    I forgot to mention, but I also played with the extrusion multiplier (both directions) and it didn’t make a difference. I’ve also gone through the klipper docs and TeachingTech’s calibration guide, the printer is fairly well calibrated at this point.

    • FuglyDuck
      link
      fedilink
      English
      4
      edit-2
      15 days ago

      How’s your temperature? Could be printing too hot. Both on the nozzle and the bed.

      • @AjenOP
        link
        English
        215 days ago

        It’s hot - 60 bed, 220 nozzle. I’ll try 40/200

        • @[email protected]
          link
          fedilink
          English
          215 days ago

          For PETG that’s not that hot. On my i3 clone I was usually 70 bed and 230-235 nozzle. I would try a temp tower and do what looks best. Based on what you’ve said so far, temp does seem like a possible culprit.

          • @AjenOP
            link
            English
            315 days ago

            This is PLA, I can’t get PETG to stick to the “PEO” bed plate.

            • @[email protected]
              link
              fedilink
              English
              114 days ago

              Ah, sorry. That does sound a bit hot for PLA. I still suggest a temp tower. If you’re having bed adhesion issues, have you cleaned your bed with dish soap lately? Be sure to use only paper towel to clean/dry it - not a sponge or towel. If that’s impractical, I’ve found Windex to work better than IPA.

        • FuglyDuck
          link
          fedilink
          English
          215 days ago

          I’d suggest taking it down to 210, 215. a bed at 60 should be normal. If you have one take an IR thermometer and read off a sheet of paper (or a 1-layer print. the thermometers aren’t so good at reading glossy surfaces.) IIRC, for most PLA’s the glass transition temperature is around 70 so 60 should be right there.

          Glass transition is where the plastic begins to soften and be bendable/moldable.

          • @AjenOP
            link
            English
            115 days ago

            40/200 looks the same as 60/220. I can try 60/210 but I don’t think it will be any different.

          • @AjenOP
            link
            English
            115 days ago

            I tried printing a disk with the bed at 70c and it looks better. Going to try with it even higher. This sheet has a +0.350 z offset compared to my normal PEI sheet, so that might contribute to low heat conduction.

            • FuglyDuck
              link
              fedilink
              English
              115 days ago

              Careful. Too high and you will get failed prints. (Somewhere around the glass transition temp,)