You know, I used to do this as a teenager, when cleaning my bearings with acetone, and I recall my family needing to get the sink repaired due to leakages getting quite severe at times.
Only through this post have I come to realise, 20 years later, that I was most likely at fault for the issue.
I mean I’m still not going to admit it to anyone, but it’s good to know and stuff.
90%+ rubbing alcohol and rock salt actually does a really good job, it just takes more elbow grease. Still won’t be as clean as literally fucking dissolving it, but that’s how I’d do it if I couldn’t use acetone.
The gold standard for party bongs is shitpipes. Dunno about other places but for a Euro standard one, you need, bottom to top, 1x 100mm end cap, 1x 100mm sleeve (pipe to pipe coupling), 1x 100mm adapter to 40mm (the 100mm side should fit the sleeve), some length of 40mm pipe, some means to drill two holes, and two things not available at any random hardware store: a preferably metal what’s it called in English the thing that goes into the water and some tissue to tighten that metal thing in its hole, wrap in a taper and twist in. Try to get an adapter that’s angled, there’s also ones with a flat step instead of (quite aggressively) tapering the diameter.
Completely and utterly indestructible at least when it comes to banging it up. In principle also fit to handle acetone those Euro standard pipes are polypropylene but I wouldn’t push it. Tons of water in there, definitely bottom-heavy, and very light when empty.
You really don’t clean it you let it get gunky, just replace the water, it’s not like the gunk would dissolve into there. If you really have to, just spend what five to ten bucks on new hardware. Euro pipes should in principle hold up to acetone they’re PP but eh, why. If it works it’s probably still going to make the thing unsable for a week or so.
I always thought the same, and I’ve been toking for about two decades. For pieces my friends and I always prefer glass. If using a glass piece though, it’s important to use vinegar once in a while (not just Isopropanol) to get rid of the chance of mould build up.
![[OC] Acetone: A Thread](https://lemmy.dbzer0.com/pictrs/image/7c9f1c44-b5ac-4819-a85f-4700fd1967be.webp){kind=link}
You know, I used to do this as a teenager, when cleaning my bearings with acetone, and I recall my family needing to get the sink repaired due to leakages getting quite severe at times.
Only through this post have I come to realise, 20 years later, that I was most likely at fault for the issue.
I mean I’m still not going to admit it to anyone, but it’s good to know and stuff.
I had a bong as a freshman. I cleaned it with acetone. I then had several tubes instead.
Never understood why folks used acrylic bongs, like, how do you clean it? I kinda figured they were meant as disposable party bongs.
90%+ rubbing alcohol and rock salt actually does a really good job, it just takes more elbow grease. Still won’t be as clean as literally fucking dissolving it, but that’s how I’d do it if I couldn’t use acetone.
I use 70% isopropyl and it dissolves everything except for a film around the inner chamber.
Like a lump of tar just stops existing as a solid thing. Looks interesting after like 6 hours.
The gold standard for party bongs is shitpipes. Dunno about other places but for a Euro standard one, you need, bottom to top, 1x 100mm end cap, 1x 100mm sleeve (pipe to pipe coupling), 1x 100mm adapter to 40mm (the 100mm side should fit the sleeve), some length of 40mm pipe, some means to drill two holes, and two things not available at any random hardware store: a preferably metal what’s it called in English the thing that goes into the water and some tissue to tighten that metal thing in its hole, wrap in a taper and twist in. Try to get an adapter that’s angled, there’s also ones with a flat step instead of (quite aggressively) tapering the diameter.
Completely and utterly indestructible at least when it comes to banging it up. In principle also fit to handle acetone those Euro standard pipes are polypropylene but I wouldn’t push it. Tons of water in there, definitely bottom-heavy, and very light when empty.
You really don’t clean it you let it get gunky, just replace the water, it’s not like the gunk would dissolve into there. If you really have to, just spend what five to ten bucks on new hardware. Euro pipes should in principle hold up to acetone they’re PP but eh, why. If it works it’s probably still going to make the thing unsable for a week or so.
Now that’s science.
I always thought the same, and I’ve been toking for about two decades. For pieces my friends and I always prefer glass. If using a glass piece though, it’s important to use vinegar once in a while (not just Isopropanol) to get rid of the chance of mould build up.
Let’s just all start smoking with acetone as our bong water! So many problems solved :)
At least you know why your sinks continue to melt now
Except admitting it to 50,000 lemmy users, haha. No worries, I didn’t know acetone ruins pvc until this post either.