I have a network set up something like the following:

Device A <---> Router A <---> Router B <---> Device B

where Router A is a tp-link Archer AX73, and Router B is a tp-link Archer C7. Router B is flashed with OpenWRT, and Router A is using stock firmware. Router B is set up to be a wireless bridge between Router A’s network, and its own (it was set up using this guide).

What I am wondering is if Device A can find, say, Device B.local, using Avahi (assuming Device A, and Device B both have Avahi installed, and running), over this bridged network. So far, I haven’t been able to get it to work, so I’m wondering if it is possible at all. I have read that Avahi only works on a local network, but I was wondering if it could be bridged.

UPDATE (2024-01-16T01:28Z):

The issues that I mentioned in this post have since been solved. The majority of the issues stemmed from the fact that the relay software that I was using, relayd, doesn’t support ipv6. All the tests that I was conducting were defaulting to ipv6, so it was appearing like the bridge was failing unpredictably. Since that realization was made, and countermeasures were enacted, the problem was solved.

  • KalciferOP
    link
    fedilink
    arrow-up
    1
    ·
    10 months ago

    Router B is bridging Device B to Router A’s network, so they aren’t on separate vlans; thus, it shouldn’t require an mDNS reflector as that repeats mDNS between separate subnets.

    • eutampieri@feddit.it
      link
      fedilink
      arrow-up
      1
      ·
      10 months ago

      Then I don’t understand your topology. However, I still think you need the reflector on both routers

      • KalciferOP
        link
        fedilink
        arrow-up
        1
        ·
        10 months ago

        Afaik, an mDNS reflector is only needed to cross subnets – both subnets and mDNS function on layer 3. Bridging occurs on layer 2, and since mDNS functions in layer 3 (ipv4 multicast is layer 3), the bridge itself is invisible to it.

        • eutampieri@feddit.it
          link
          fedilink
          arrow-up
          1
          ·
          10 months ago

          This works if B has an interface that is connected to the A subnet, but not if you have a PtP between the two routers

          • KalciferOP
            link
            fedilink
            arrow-up
            1
            ·
            10 months ago

            This works if B has an interface that is connected to the A subnet

            I’m not sure I understand exactly what you mean. Is it not given that if two routers are connected to each other then an interface from either of them will be connected to the other?

            but not if you have a PtP between the two routers

            What do you mean by PtP? Are you referring to something like WDS, or, in my case, relayd?

              • KalciferOP
                link
                fedilink
                arrow-up
                1
                ·
                edit-2
                10 months ago

                Wait, are you just generally referring to this? That already exists in the form of PPPoE, and, for all intents and purposes, WPA, does it not?

                • eutampieri@feddit.it
                  link
                  fedilink
                  arrow-up
                  1
                  ·
                  edit-2
                  10 months ago

                  No, not at all 🙂. I’m referring to a configuration in which the two routers are linked through another subnet (using a separate link between the two) and this link is the point to point link. You usually assign a /30 so you can have an address for each router. ~This way the traceroute shows three hops instead of just two.~ However, since you’ve already told us that this is not your setup, what I’m saying shouldn’t matter to you. If you’re curious though, let’s keep talking :)

                  Edit: striked mistake

                  • KalciferOP
                    link
                    fedilink
                    arrow-up
                    1
                    ·
                    10 months ago

                    Interesting, where does the 3rd hop come from? Wouldn’t the routing table just point from one router to the other – so 2 hops?